PVC护墙板的施工工艺

1、丈量墙面。先丈量出须要装置墙板的长度，依据这个尺寸来截取铝合金的长度。依据护墙板的尺寸盘算出所须要的护墙板整数块是多少，过剩的空间用护墙板拼板实现即可。

2、在截取好的铝合金上钉好牢固孔，依照P铝合金上的孔的间距在墙面上打好孔，用收缩螺丝或钢钉将踢足线挂钩牢固在墙上。

3、装置顶角线，个别在其两侧涂上公用胶，而后将其粘到顶角处，再拉开数分钟，而后再牢牢粘上即可。湿度高的地域两根踢足线联合，须留出恰当的伸缩缝，特殊在放家具的墙角，伸缩缝更应多斟酌一些。

4、装置护墙板，将护墙板从左到右拔出踢足线内，肇端块应从墙角开凹槽向墙角。在距护墙板上口1.5cm处安上收缩螺钉或钢钉，留神螺钉不能显露护墙板面。在腰线凹槽内涂上公用胶，过多少分钟后插到凹凸面即可，在墙角处必需45°对角。

5、在铝合金的卡口上装置橡胶防撞条，保左右封口安插在护墙板两头，截取PVC面板的长度，把面板笼罩在铝合金上，装置实现。

6、当装置至最后时，转角的两个边沿须要涂上公用胶，始终粘到顶角处，而后再拉开一会再牢牢粘上。这会增添护墙板的牢度，增添它的应用寿命。

1, measure the wall. The length of the wall plate to be installed is measured first, and the length of the aluminum alloy is intercepted according to this size. According to the size of the wall-guard board, the number of integral blocks of the wall-guard board is calculated, and the excess space is realized with the wall-guard board.
2, nail a solid hole in the intercepted aluminum alloy, according to the spacing of the holes on the P aluminum alloy, hole in the wall, with contraction screw or steel nail to hook the kick line firmly on the wall.
3, the device top corner line, individual on its two sides coated with public glue, and then stick it to the top corner, open for a few minutes, and then firmly adhere to it. Humidity high area of the two kick line Union, must leave the appropriate extension seam, special in the corner of the furniture, the extension seam should be considered more.
4, install the wall-guard, the wall-guard from the left to the right pull out kick foot line, the end of the block should be from the corner open groove to the corner. Insert a contraction screw or steel pin 1.5 cm from the top of the wall-guard. Note that the screw can not reveal the wall-guard surface. Public glue is applied to the waist groove, and after how many minutes it can be inserted into the concave surface. It must be 45 ° diagonal at the corner.
5, installed on the aluminum alloy bayonet rubber collision bar, ensure that the left and right seals are placed at both ends of the wall-guard board, intercept the length of the PVC panel, cover the panel on the aluminum alloy, the device is realized.
6, when the device to the end, the two edges of the corner must be coated with public glue, always stick to the top corner, and then pull a few more time before firmly sticking. This will increase the fastness of the wall-guard and increase its application life.